作為感應門的控制裝置，感應門控制器如果損壞就會導致感應門停門無法運行，那么你知道感應門控制器如何正確接線嗎？在接線時又有哪些注意事項嗎？今天門道佰分佰小編就根據日常維修感應門控制器的經驗為大家簡單介紹一下。

As the control device of the induction door, if the induction door controller is damaged, it will cause the induction door to stop and cannot operate. Do you know how to correctly connect the induction door controller? Are there any precautions when wiring? Today, doorway Baifen Xiaobian will give you a brief introduction based on the experience of daily maintenance of sensitive door controller.

怎么安裝自動感應門？

How to install automatic induction door?

感應探測器探測到有人進入時，感應探測器將收集信號，生成脈沖信號，其后脈沖信號傳給主控器，主控器判斷后通知馬達運行，同時監控馬達轉數，以便通知馬達在一定時候加力和進入慢行運行。馬達得到一定運行電流后做正向運行，將動力傳給同步帶，再由同步帶將動力傳給吊具系統使門扇開啟;門扇開啟后由控制器作出判斷，如需關門，通知馬達作反向運動，關閉門扇。

When the induction detector detects someone entering, the induction detector will collect signals and generate pulse signals, which will then be transmitted to the main controller. The main controller will notify the motor to run after judging, and monitor the motor revolution at the same time, so as to inform the motor to apply force and enter slow operation at a certain time. After the motor receives a certain operating current, it operates in a positive direction and transmits the power to the synchronous belt, which then transmits the power to the spreader system to open the door leaf; After the door leaf is opened, the controller makes a judgment. If it is necessary to close the door, inform the motor to move in the opposite direction and close the door leaf.

自動感應門怎么接線的？

How is the automatic sensing door wired?

自動門感應器一般有七個部件，分別是皮帶張緊輪部件、接線架裝置、動力梁、通用調節型吊架、微電腦智能控制系統、動力裝置、皮帶部件。在接線時要先將原配線插在感應器里，感應器中有一個插座，插好即可。然后將線的另一頭連接在端子另一邊。連接時注意線的顏色，相同顏色的是信號線，不同顏色的是電源線。安裝好之后，將自動門感應器固定在門框上，距離地面高度不低于2.5米。

The automatic door sensor generally has seven components, including belt tensioner, wiring rack device, power beam, general adjustable hanger, microcomputer intelligent control system, power device and belt component. When wiring, insert the original wiring into the sensor first. There is a socket in the sensor. Just plug it in. Then connect the other end of the wire to the other side of the terminal. Pay attention to the color of the line when connecting. The signal line with the same color and the power line with different colors. After installation, fix the automatic door sensor on the door frame, and the height from the ground shall not be less than 2.5 meters.

如果濟南感應門安裝了輔助光線傳感器(紅外對射保護裝置)，當自動門門扇打開時，人站著不動，用手遮擋輔助光線傳感器，門應該保持打開狀態。當手離開后幾秒內，門應該重新關閉。

If the Jinan induction door is equipped with an auxiliary safety light sensor (infrared radiation protection device), when the automatic door leaf is opened, people stand still and block the auxiliary safety light sensor with their hands, the door should remain open. The door should be closed again within a few seconds after the hand leaves.

感應門安裝一定要選擇有實力和豐富經驗的安裝公司進行施工，因為感應自動門安裝具有易學難精的特點，沒有豐富的安裝經驗，感應門運行時經常會有這樣或那樣的缺陷，而且通常難以，同時也難以保正有完善的售后服務。更多相關內容就來我們網站http://www.7789822.cn咨詢吧！

The installation of induction doors must be carried out by a professional installation company with strength and rich experience, because the installation of induction automatic doors is easy to learn and difficult to refine. Without rich installation experience, induction doors often have one or another defects when running, which are usually difficult to eliminate, and it is also difficult to ensure perfect after-sales service. Come to our website for more relevant content http://www.7789822.cn Consult!